Product Details:
Payment & Shipping Terms:
|
| MATERIAL: | S355JR | APPLICATION: | ELECTRICITY DISTRIBUTION |
|---|---|---|---|
| THICKNESS: | 2.5-10MM | SHAPE: | POLYGON |
| GALVANIZATION: | ASTM A123,average Coationg Not Less Than 85um | WELDING: | AWS D1.1,penetration 100% |
| LIFETIME: | 50 YEARS | WIND SPEED: | 160KM/H |
| ULTIMATE TENSILE STRENGTH: | 490-620MPA | ||
| High Light: | 16m steel tubular pole,1000 dan steel tubular pole,electrical project steel tubular pole |
||
Specifications:
| Height | From 9 meter to 100 meter |
| Suit for | Electric Power Transmission and Distribution |
| Shape | Polygonal or Conical |
| Material |
Normally Q345B/A572, Minimum Yield Strength ≥ 345 N/mm² Q235B/A36, Minimum Yield Strength ≥ 235 N/mm² As well as Hot rolled coil from ASTM A572 GR65, GR50, SS400 |
| Power Capacity | 10kV to 220kV |
| Tolerance of the dimension | According to client’s requirement. |
| Surface treatment |
Hot dip galvanized Following ASTM A 123, or any other standard by client required. |
| Joint of Poles | Slip joint, flanged connected |
| Standard | ISO 9001:2008 |
| Length of per section | Within 14 meter once forming |
| Welding Standard | AWS (American Welding Society ) D 1.1 |
| Thickness | 1 mm to 36mm |
| Production Process |
Raw material test → Cutting →bending →Welding (longitudinal ) →Dimension verify →Flange welding →Hole drilling →sample assemble → surface clean→ Galvanization or powder coating , painting →Recalibration →Packages |
| Packages | Packing with plastic paper or according to client’s request. |
Steel
Descripition of material:The material is in accordance with NF EN 10025
Standard and NF EN 10149 Standard,it has the following property.
-Yield Strength=355N/mm2
-Toughness remains the same under 20 degrees below zero.
-Galvanization is in accordance with NFA35503 Standard Class 1.
Galvanization
Standard:NFA91121
Average thickness of the galvanization:Not less than 86μm.
Installation
-Remove all the equipment on the pole during Assembly.
-Circle a sling around th epole shaft of each section.
-Fix the sling on top section to one pulley block.
-The sling on the bottom section is tightly fixed and fixed at the center of gravity.
-Make the steel pole vertical by tighten the sling of the top section.
-Fix the steel pole.
-Remove the sling.
Company Introduction:
Jiangsu Milky Way Steel Poles which established on 1991 is located in Wuxi,East of China ,near one of the largest sea port of China ,Shanghai,Port .
Our Company has 24 years experience on producing the steel poles including the transmission power pole,street light pole,high mast pole and so on.
We exported to oversea countries since 1991 and our products have been delivered to more than 70 countries and areas ,including America,Australia ,Russia ,Germany ,Span,Philippines ,Malaysia,Africa and so on.
We are the supplier of many big project in many countries,like the street light pole of Dubai Tower.the high mast pole for Sochi Winter Olympic Game and so on.
Professional Direct Buried Q345 15m Metal Utility Poles Octagonal Cross Section Shape
Hot dip galvanization electrical power pole for over headline project
Conical 3.5mm thickness electric power pole 22m height with three sections for transmission
3mm Thickness NGCP Electrical Power Pole For Electricity Distribution
Transmission Line Project Electrical Power Pole 18m 10KN For Electricity Distribution
Power Line 11m 8KN Electrical Power Pole With Galvanizing Surface Treatment
Anticorrosive 14m 500Dan Steel Power Pole For Power Transmission Electric Line
Electricity Distribution 12m Tubular Steel Power Pole For Transmission Line Project
11.8m Height Spray Paint Galvanised Steel Poles For Transmission Equipment
12m Gr 65 Material Galvanized Steel Pole Round Electric Transmission Line Poles
12m S355 S500 Steel Power Pole ASTM A123 Galvanized For Street Lighting
Multi Sided Single Circuit Galvanized Steel Pole For Electrical Line 132kv
